Which Wi-Fi router should I choose for Beeline home Internet? Smart Box from Beeline How to set up a Beeline white dot router.

The purpose of this guide is to write the most comprehensive and detailed instructions on how to set up Wi-Fi D-Link router DIR-300 NRU for working with the Beeline provider. We will tell you step by step how to connect the router and what settings on your computer you should pay attention to, how to set up an L2TP connection for Beeline, as well as wireless network settings. We will separately touch on the configuration of Beeline television. In general, the goals have been set, let's begin.

Before you start setting up the DIR-300

First of all, I will note for which ones wireless routers This instruction is written, it is completely suitable for:

• D-Link DIR-300NRU B5 (Firmware 1.4.3, 1.4.9)
• D-Link DIR-300NRU B6 (Firmware 1.4.3, 1.4.9)
• D-Link DIR-300NRU B7 (firmware 1.4.8 or other 1.4)

Finding out which version of the router you have and which firmware you have is quite easy - just look at the sticker on the back of it.

The next thing to talk about is the firmware Wi-Fi router A. You don't have to do this, but it is possible that without the latter, or at least relatively new firmware Your router will not work very stable, especially with Beeline. The latest firmware for D-Link DIR-300NRU routers has the index 1.4.x - we will consider the settings for this firmware here. You can read about how to update the router firmware in the “Firmware” section on this site, and also see it in the video below.

I also note that if your router has firmware 1.3.0 or another 1.3 installed and you do not plan to update it, you can also use this guide - setting up the router is the same, all you need to do is click “Configure manually” ", further setup steps are no different.

Beeline firmware - the one that is offered for installation on the provider's official website - is not something that I can recommend. You can install it, but, if necessary, returning the factory firmware version from D-Link is not a trivial task.

Connecting D-Link DIR-300 to a computer

I hope this will not be difficult for you - the Beeline cable is connected to the Internet port on the back of the router, and the router is connected to the computer using the network cable that is included with the device. After this, you just need to plug the router into a power outlet.

Note: do not start the Beeline connection on your computer after you have started setting up the router - neither before nor after. IN otherwise, you will get the situation that users most often encounter - there is Internet on the computer, but it connects via Wi-Fi, but does not work. The thing is that from now on (after the setup is completed), the connection will be established by the router itself, and then “distributed” to other devices, and if you start the Internet on your computer, the router will not be able to install it. In general, remember: do not launch the Internet on your PC during and after setting up the router, the Internet will be available via local network.

1. In Windows 7 and Windows 8, go to Network Sharing Center and shared access, then select “Change adapter settings” on the left. Right-click on the local connection with which you are connected to the router, click “Properties” and go to the third item.
2. In Windows XP, go to Control Panel - Network Connections and right-click on the local connection icon, select "Properties" in context menu and move on to the next step.
3. In the list of components used by the connection, select Internet Protocol Version 4 TCP/IPv4 and click the Properties button at the bottom right.
4. Make sure that the IP address and DNS server addresses are obtained automatically (as in the picture), if this is not the case, bring it into compliance.

Setting up an L2TP Beeline connection on a D-Link DIR-300 router

The first and main task when setting up a Wi-Fi router is to force it to establish a connection to the Internet instead of a computer. The Beeline Internet provider uses a connection using the L2TP protocol, which is what we will configure now.

Note: if you have previously tried to configure yourDIR-300, but unsuccessfully, reset it to factory settings - to do this, press and hold (with the router turned on) the buttonReset the back for 10 seconds, then release it.

First of all, launch your favorite browser and enter 192.168.0.1 in the address bar and press Enter - as a result, you should be prompted for a login and password to enter the router settings interface. Enter the standard values ​​for the D-Link DIR-300 NRU router - admin in both fields.

The next thing you will see is a request to change the factory password, and then the main router settings page, where we will perform all the actions.

On the next page, click the "Add" button.

Now the most important thing is to configure the L2TP connection parameters for Beeline in the router. Fill in the fields as follows:

• Connection type - L2TP + Dynamic IP
• Name - any connection name, not used anywhere, can not be changed
• Username and password - your Beeline data
• VPN server address - tp.internet.beeline.ru
• The rest of the data does not need to be changed: if you have any doubts, simply copy it from the image shown - it shows the working parameters for Beeline.

Click the "Save" button. After this, you will again see a page with a list of connections, where the connection you just created will be located and it will be terminated. There will also be an indicator at the top of the page notifying you that the router settings have been changed and need to be saved. Do this (i.e., we save the total twice - this is necessary so that after turning off the router from the network, the settings are not reset).

Wait a minute and refresh the page. If you did everything correctly and did not forget to turn off the Internet on your computer, then you will see that the newly created Beeline connection is in the “Connected” state - i.e. Internet from this computer is already available. All that remains is to configure the wireless network settings, set a Wi-Fi password and, if necessary, set up IPTV television.

Setting up a wireless network on D-Link DIR-300

In order to set up Wi-Fi on the D-Link DIR-300 router, on the router’s advanced settings page, in the Wi-Fi item, select “Basic settings”, then fill out the following fields:

• SSID - here you should indicate the desired name of the wireless network, in Latin letters and numbers, you will see it when connecting to Wi-Fi from a laptop, phone or other device and it will allow you to distinguish your network from others.
• The remaining points can be left unchanged. Click the "Edit" button

After that, on the same Wi-Fi tab, open the “Security Settings” item and fill it in as follows (recommended):

• Network Authentication - WPA2-PSK
• PSK encryption key - the desired Wi-Fi password, at least 8 characters, Latin and numbers.
• Click "Edit"
• Click “Save Settings” next to the indicator at the top of the page.

That's all, the router is configured and now you can use the Beeline Internet from any device equipped with a Wi-Fi module.

Setting up Beeline television on DIR-300

In order to set up Beeline television (IPTV) on this router, no special skills are needed. Just go back to home page router settings at 192.168.0.1, select “IP television”, then indicate which port will be used to connect the Beeline TV set-top box. Click change, and then at the top - save. That's all, the TV setup is complete.

If something doesn't work or doesn't work out, you can write in the comments. In the future, a section is planned on the site with solutions to the most typical problems that arise during setup various Wi-Fi routers, but since there is no such section at the moment, I will try to answer here quickly.

And if everything worked out for you, leave a comment too.

The most functional WI-FI router from Beeline is Smart Box ONE, which is used when connecting home internet and TV. The cost of the device is 2500 rubles. If there is no wired Internet, then you can use the ZTE MF90 4G router.

The latest models of Beeline wireless modems are equipped with a more powerful signal transmitter that operates in two bands - 2.4 and 5 GHz, so you don’t have to worry that some device won’t connect to the Internet. An advanced processor at the maximum level ensures the reliability of the WI-FI signal.

The device has the following advantages:

1. The maximum transfer speed is 300 Mbit/s.
2. The 802.11n standard, which is supported by almost all devices.
3. Supports digital TV connection.
4. Convenient interface for configuration.
5. Modern design.

The 4G router provides network access at speeds of up to 74 Mbit/s. It comes with a SIM card that allows you to use 30 GB of Internet per month. The monthly fee is 1200 rubles.

Connection and setup 4G/WI-Router FI

Connecting the router is quite simple; you need to connect the power cable, as well as the Internet cable that runs into the room. In order to connect the device to the network, you need to connect the computer to the device using a network cable via a LAN connector. The 4G router connects to the computer via a USB connector.

1. After all the lights on the device light up, you will need to open a browser on your computer and go to 192.168.1.1. After this, the welcome page of the interface should open.
2. To gain access to quick setup, you need to enter your login and password. IN standard setting The login and password are “admin”.
3. After logging in, the main menu will open. If the user is not experienced, then it is recommended to go through the procedure quick setup. If you are well versed in such matters, then you can go to the advanced settings menu.
4. Quick setup consists of four steps:

Home Internet. In this section you can connect the device to the Beeline network. All the necessary parameters are already contained in the device firmware.

WI-FI network. This item allows you to set wireless network access parameters. In this section you must enter the network name and password. The password must be at least 8 characters.

Guest network. Here you can configure guest Internet access.

TV. IN in this case you need to select the LAN port through which the IPTV set-top box will be integrated, if you have one.

When the router establishes a connection, the “Status” line will say “Internet connected.” At this stage, the setup is completed and you can fully use the Internet.

Setting up a 4G router is done in the same way.

Software update

The operation of the device is controlled by its firmware, which needs to be updated from time to time in order to prevent malfunctions in its functioning. The firmware should be updated carefully, because if anything goes wrong, service center you can't escape.

1. The latest software must be downloaded from the official website.
2. Open the page in the browser 192.168.1.1 .
3. Login to the menu occurs by entering your login and password (enter admin in both fields).
4. Next, you need to go to the advanced settings menu and select “Other” at the top of the page.
5. A list of settings will appear on the left side, where you need to select “Software Update”. At this point you need to select the folder in which the downloaded firmware is located.
6. Click on the “Update” button and do not touch anything so as not to disturb the settings.
7. After a short period of time, the router will automatically reboot and be ready for use.

The 4G router firmware is not updated.

Beeline is one of the TOP Internet providers that operates even in the most remote areas of Russia. This organization provides access to any type of Internet - both home and mobile. But to save money, most people started using a wi-fi router.

The router can be purchased at almost all points of the Beeline operator. But sometimes setting up a router from this supplier becomes a real problem for an unprepared person. We will help you sort this out.

In general, the process does not require special knowledge, and every person can cope with this task. To do this, you do not need to call a specialist and overpay.

Reference! To connect different scheme connections and installation are the same.

1. If the router is new, you should unpack it and then connect the power adapter.
2. Choose a convenient location where the equipment will be located.
3. Connect to the Internet via wi-fi or cable.
4. Connect your laptop or computer to set up.
5. Connect your router to the mains.
6. Set up the router (to do this, follow the link that is written on the bottom of the router, next to it you will find your username and password).
7. Set up the Internet (discussed below).
8. Configure your wireless network settings and change your username and password.

Setting up a router for Beeline - ASUS

If we consider a router with reverse side, you will see 4 identical holes in yellow and one in blue (for the Internet). Insert the wire from Beeline into the blue port, and connect the wire to the PC into the second one. With its help we will configure the router. Next, extend the antennas and connect the router to the Network.

Important! Before you start installation, check the type of connection (in the propertiesIPv4 you must register the connection to acceptIP addresses and servers automatically!). Otherwise, this may cause network errors upon further connection.

Connection procedure

1. Launch any browser, enter 192. 168. 1 in the address bar.

   

2. Next, we indicate the parameters (basic login and password, which is written on the bottom plate of the device).

   

3. Go to the WAN/Internet section.

   

4. Set the connection type to L2TP/L2T and dynamic IP (if available).

   

5. Specify the login and password issued by the provider (written down in the contract).

   

6. Enter the host name, indicating the address tp.internet.beeline.ru, and select one of two values ​​- PPTP or L2TP.

   

7. Check the operation of the router: just enter any website and see if it loads or not.

Attention! To ensure proper operation, before starting setup, remove the connection type that was previously used.

Launching Wi-Fi for ASUS RT-N12

1. We launch the browser and enter the standard numbers 192. 168. 1 and enter the password indicated on the back of the router box (admin, admin).

   

2. Go to the Wireless Networks section called wireless.

   

3. Next, in “SSID” we indicate the name that you choose yourself. To protect your data, use strong passwords with English letters and numbers (you can also use capital ones). Save.

   

4. Network authentication – WPA Personal.

   

5. Write your password and confirm it again.

   

6. To commit your changes, click “Save.”

   

If you have completed the steps correctly, you can start using the Internet.

Setting up a router for Beeline: TP-Link

Important! Before you start installation, check the type of connection (in the IPv4 properties the connection must be set to accept the IP address and server automatically!). Otherwise, this may cause network errors when you continue connecting to the Internet.

Connection procedure

1. Open any browser, enter 192.168.

   

2. We write down the login and password specified by the manufacturer.

   

3. Open the “Internet/WAN” section.

   



4. In the “Connection type” line, indicate L2TP/Russia L2TP.

   

5. We register the login and password issued by the provider (specified in the contract).

   

6. Our host name is tp.internet.beeline.ru.

   

7. Check the operation of the router by clicking on any link.

Setting up a router for Beeline: D-link DIR-300

If you look at the router from the back, you will see 4 yellow holes and one blue hole (for the Internet). Insert the wire from Beeline into the blue port, and connect the wire to the PC into the second one. With its help we will configure the router. Next, extend the antennas and connect the router to the Network.

Important! Before starting installation, check the type of connection (in the IPv4 properties, the connection to obtain an IP address and server must be specified automatically!). Otherwise, this may cause problems with your future Internet connection.

Connection procedure

1. Enter 192. 168. 1 in the browser.

   

2. We write the name and password specified by the manufacturer on the back panel of the router.

   

3. In connection types, select L2TP.

   



4. Fill in the server name by entering the address tp.internet.beeline.ru.

   

5. Uncheck the “Without authorization” and “Enable RIP” checkboxes.

   

Next wi-fi settings

Beeline Internet setup: home router

For a home router, Beeline recommends all models of Smart Box routers. Their distinguishing feature– speed, number of holes for USB and range (can be in the range from 2.5 to 5 GHz). Setting up such a router will be even easier thanks to the connection device. During installation, you will only indicate your region of residence and the name of the locality, and everything else will be configured automatically.

Connection procedure

• connect the Internet cable to a special port (it will be marked in a different color, there is only one);
• We connect the PC to the router with a small wire that will be included with the device.

1. Open any browser and enter 192.168.1.1. Click Continue.

   

2. Enter the standard login and password admin, admin.

   

3. From the main menu, select Quick Setup.

   

4. In the “Home Internet” section, enter your username and password in the appropriate fields specified when concluding the agreement.

   

5. As a preliminary key, we come up with a name and password, which will contain at least 8 characters.

   

6. Click "Save".

   

Important! Before checking the Internet, reboot your router.

Video tutorial on setting up a Smart Box router

If you follow all the instructions, you can do it yourself and quickly. If something doesn't work, try again or call a specialist.

Video - Setting up Wi-Fi router ASUS RT-N12 for Beeline

This technical guide will help you connect your router to the Internet with an L2TP wan connection type (for example Beeline). The router model doesn't matter. The only difference is different manufacturers routers, in the layout of settings functions and menu item names in the administrative mode of the device. The guide is suitable for all providers using L2TP connections!

Setting up the router

1. On the router, find the WAN port (usually the port is blue). We insert it into twisted pair from an Internet provider, which previously could have been connected directly to the computer if you had not previously used a router. Then we find several yellow LAN ports there. In any of them we insert network cable which came with the router, and the other end into the network card on the computer.

2. On a PC or laptop running OS Windows 7, open the section network settings: Start - Control Panel - Network and Internet - Network and Sharing Center - Management network connections— Changes in adapter parameters.

Right click click on the “Local Area Connection” item, go to “Properties”, then go to the Internet Protocol “TCP/IPv4” section and select the following items “IP automatically” and “ DNS servers automatically"

Click "OK".

3. On the router we look for the IP address that is used to enter the router settings (by default - 192.168.0.1), and login with password (often login: admin, password: admin)

4. Then in the browser we write 192.168.0.1 in the address bar (if it is the same on the router), and enter the login and password that we saw on the router.

6. In the “WAN Connection Type” column (Internet connection type), select “L2TP/Russia L2TP”/ We specify the login and password from the agreement with the provider. We indicate the server name: tp.internet.beeline.ru (or something else, also see in the contract). Save the settings.

7. Open the section “ Wireless network" and write our values ​​for the points:

• SSID - name of the wifi network.

• Network Security - WPA2-Personal
• Encryption - AES or TKIP
• Secret key - Wi-Fi password, at least 8 characters.

8. Apply the settings. We log in from a device that should receive the Internet (it must have a Wi-Fi module). Click on the icon wireless connections(in the lower right corner of the Windows icons, next to the clock). We find our network in the list and connect, enter the password (one that contains at least 8 characters).