iPad won't boot. iPad won't turn on: how to fix it? Possible problems, recommendations

Owners of tablet computers Apple iPad They consider their equipment so reliable that sudden failures and malfunctions throw people into a stupor. If your iPad does not turn on, there is no need to be afraid - any situation can be corrected. It is quite possible that it did not break, but simply hung, because software failures are not particularly uncommon. In this review we will look at all situations and find out what to do if the tablet computer iPad Doesn't turn on or charge.

If the iPad does not turn on, the problem may lie in a low charge level battery. A deep discharge often results in tablet computers not turning on at all or turning off within one or two minutes after starting. Therefore, the first thing you should do in this situation is to put the tablet on charge and leave it alone for several hours. During this time, the battery will charge and you can try to turn on the iPad again - most likely, the new attempt will be successful.

Have you charged your iPad, but it turns out that it won’t turn on again? In this case, you need to check the functionality charger. It may not provide the required charging current, preventing normal charging of the battery. If you leave the iPad to charge for a long time, it will have absolutely no effect if the charger is broken. To check the functionality of the charger, use another tablet or iPhone. You can also try a different charger on your tablet or even try to recharge from the USB port of your computer.

If you are sure that just a few hours ago the battery was full, still put your tablet on charge - it is possible that in these few hours the battery has been completely discharged.

Making a reset

Desktop computers and laptops appeared much earlier than tablet computers. Experienced users who work a lot on computers know very well that if the equipment shows signs of completely frozen and is not going to restore its functionality, you should click on the “Reset” button. In the case of laptops that do not have this button, you need to press and hold the power button - after a while the laptop will turn off, after which it can be started and booted again.

What to do if your iPad won't turn on? You need to try to force the tablet to reboot. You must also ensure that all data in the internal memory remains intact. Since there is no “Reset” button on the iPad, we will proceed in a different way - hold down the power button and the Home button, hold them for 10 seconds and wait until the tablet reboots (a bitten apple should appear on the screen). As soon as the iPad restarts, its functionality will be restored.

Please note that this reboot method does not result in any loss of user data. But periodic backups never hurt anyone.

iPad recovery

At your disposal is iPad tablet 2, iPad mini or any other type of tablet from Apple? Your device won't turn on? It is possible that it has some kind of fatal software failure that prevents normal functionality. In some cases, even a reset does not help here. What to do?

You should try restoring your tablet computer - in this case it will return to the state in which it left the factory. To perform recovery operating system, you must perform the following steps:

• Turn off the tablet completely - its display should go dark;
• Connect your iPad to your computer and launch iTunes;
• Hold down the power button and the Home button on the iPad and wait 10 seconds;
• Continue holding the Home button for another 10 seconds.

After this, iTunes will notify that it has detected a device connected in recovery mode - then the program will begin to restore the iOS operating system by downloading the firmware. Once the procedure is completed, the iPad will reboot and turn on (if there are no other problems on board).

This method is very radical, as it provides complete removal data from internal memory. Therefore the presence backup copy for their restoration is mandatory.

Moisture ingress

The iPad does not turn on - the apple lights up and then goes out. What to do in this situation? If the problem occurs after getting wet, you must urgently take the tablet to the nearest service center. Here it will be carefully disassembled, cleaned and dried, after which it will be checked for functionality. And you don’t need to listen to advice on cleaning yourself - this way you can only harm your electronic assistant. This work should be done by specialists. They will also be able to cope with other tasks of restoring the functionality of Apple tablets.

Similar behavior of the iPad, when the apple lights up on the screen and then goes out, also appears with many other malfunctions. For example, when the battery life is exhausted.

iPad won't turn on or charge

What should I do if my iPad won't turn on or charge? Such situations do not arise very often, but it is easy to identify the reason for such behavior. The problem may be related to:

• If there is a general malfunction of the device, you will have to take it to the nearest service center;
• If the battery is faulty, this is another reason to visit the service center, since batteries are changed only here;
• If the charger or cable is faulty, check the integrity of these accessories and buy a replacement (if a fault is detected).

Thus, at home we can only perform the last operation - check the cable and charger.

Self-repair and service repairs

What to do if your iPad won't turn on? You can find a lot of advice on the Internet about self-repair. We consider this advice harmful - disassembling iPads is a complex and painstaking process that requires certain skills. As for repairing electronic parts, you need experience. IN otherwise you will simply ruin your tablet, and the total cost of repairs will increase significantly - let specialists handle the repairs. You can follow the above steps and check the functionality of some nodes.

Even the best quality equipment is not immune to malfunctions. And Apple devices, which have won the love of users with their functionality and impeccable reliability, are no exception.

If your iPad won't turn on, don't worry too much. The reason for this is not necessarily a hardware malfunction; most likely, the problem can be solved easily and trivially.

The reasons for this behavior of the tablet should be determined. This may happen due to a battery failure or a faulty power button.

Causes and solutions

This behavior is usually typical for the iPad after the battery has been discharged.

Factors associated with battery damage can be divided into three groups:

• contact deformation (can occur if the tablet falls into water);
• minimum charge;
• internal problems.

Battery low

First of all, if it is impossible to turn on the iPad, it should be connected to a charger. A completely discharged battery is often the reason for this behavior of the iPad. Usually the battery charge is only enough to display an empty battery, but it often happens that nothing is visible except a dark screen.



The minimum recommended time to charge a tablet from Apple is 20 minutes. After this, you need to try to turn it off. If a red battery appears on the display, the tablet is low and you need to continue charging.

Reboot

The most effective action in the fight against spontaneous shutdown of the tablet is considered to be a hard reboot. To do this, press two keys on the iPad “Home” and “Power” at the same time and do not release them until an apple (Apple logo) appears on the screen or graphic image about the battery condition.



The appearance of an apple on the display indicates that the problem has been solved, the tablet is charging and will be available for normal operation.

It should be noted that a hard reboot resets temporary data.

Restoring the iOS operating system using iTunes

If after a hard reboot the tablet still does not turn on, you can try to restore the iPad's functionality by completely flashing the device.



In order to restore the operating system via iTunes you will need:

• the most recent iTunes version(preferably);
• pre-downloaded file from iOS version, which is currently installed on the iPad.

Restoring iOS is carried out according to the following sequence of actions:




iTunes will automatically delete all content and download the latest firmware to internal memory iPad. After the update, the device will be transferred to Recovery Mode, and the device will be restored to its factory state.

Other reasons

Often, even with a loaded battery, the iPad still does not turn on.

There may be several reasons for this behavior of the device:

• installation of unlicensed applications and installation of new firmware. A possible solution to the problem is to reinstall the operating system using iTunes. But before reinstalling the operating system, you should try to hard reboot the device;
• Problems with iPad components. Most often the power button breaks. To diagnose this problem, you need to connect the device to a charger. If the battery charge indicator is displayed on the screen, then the power button is almost certainly faulty;
• The charging connector is faulty. This type It is much more difficult to identify breakdowns, since when you connect an iPad without a charge to the charger, nothing happens. Possible way eliminating this type of malfunction - cleaning the connector contacts;
• moisture getting inside the tablet. You can try to cope with this problem yourself. You need to disassemble the tablet and let the device dry for 2-3 days. This method not always effective and risky, since there is a possibility of board oxidation. Repairing the board is usually quite expensive, and in some cases the device becomes completely unrepairable. In this regard, it is recommended to return the tablet to a service center to resolve the problem as soon as possible;
• short circuits. Despite the fact that the reason is incredible if used correctly, this can happen when using a non-original charger. The only way out of the problem situation is to replace the burnt elements.

Video: What to do, iPhone won’t turn on

iPad stuck on apple and won't turn on

The situation when an Apple tablet does not turn on and an apple is lit on the display is quite common. The likely source of the problem lies in a malfunction software. To solve this you need to install new firmware tablet using iTunes.

Except software problem The reason for this behavior may be hardware. If the internal components of the tablet malfunction, you cannot do without the help of third-party specialists.



In general, when an apple appears on the screen, you should not worry too much; most likely, nothing critical has happened to the tablet, and the problem can be solved on its own. However, in extreme cases, such as moisture getting inside the device, it is better to contact a service center.

As a rule, if an Apple tablet turns off and does not turn on, this means that there is a failure in the device's power supply system. In this case, the tablet can turn on or off on its own, periodically changing the battery charge level. Usually, with such problems, replacing the battery helps, even if the gadget was purchased recently.

Only experienced specialists can accurately answer the question of what to do when the iPad tablet does not turn on. Timely contacting a specialized service center will help you avoid more serious problems and unnecessary costs.

An iPad that stops starting is no more useful than the box from under it. However, this is not a death sentence: if the iPad does not turn on, it can certainly be brought back to life. Sometimes you can do this yourself.

First, you should make sure that the gadget is not discharged. If the battery is used up, the tablet should not work. Connect the standard charger, wait at least 15-20 minutes and press the power button. If this was indeed the problem, it should work.

Hard Reset

Let's assume this didn't help or the iPad didn't need charging in the first place. Then you should press Power keys and Home (so-called Hard Reset) for 5-10 seconds. If nothing serious has happened, after a few seconds the Apple logo should light up on the screen, after which the tablet will boot.
That didn't help either? This means the filling is faulty. What exactly - an inspection will show. Let's look at the most basic reasons:

Damage to the power connector

This part does not fail on its own. Usually it is damaged due to careless handling by the user (dropping the tablet from a height, trying to insert the plug of an incompatible charger). The pin connectors become deformed, break off, and eventually the gadget stops charging. Over time, the energy in the battery runs out, the tablet turns off and, for obvious reasons, does not start back up.

A damaged connector cannot be repaired. Theoretically, this is possible, but such work will be prohibitively expensive. It is much cheaper to replace the part with a working one. At the service center this procedure will take no more than an hour.

Worn power button

Any keys are subject to mechanical stress. The more often the buttons are pressed, the faster they become loose. A special case is when the tablet falls face down. In such a situation, both the button itself and the cable responsible for its operation may fail.

The technician's job will be to replace damaged elements.

Moisture ingress

This trouble hits the client’s pocket the hardest. Flowing into the device, the liquid spreads across the contacts, starting the corrosion process. The more moisture penetrates inside and the more complex its composition, the larger the consequences can be.

If the iPad does not turn on because of this, liquid has probably got on the contacts of the Power button, cable, or printed circuit board. The exact picture can be established after diagnosis. Then the repair time will be determined: it will range from a couple of hours to a week. The work will include cleaning the tracks from oxides and replacing damaged components.

Short circuits

A striking example is the use of a non-original charger. The charge of electricity is transferred to the power connector, and through it is transmitted to other components. Repairs are carried out by replacing faulty parts. It will take from 40 minutes to several hours.

The most important thing for any iPad breakdown is not to delay contacting the service center. The less time passes from the moment of the incident, the higher the chances of successful recovery of the gadget. Professional iPad repair.

Possible malfunctions and cost of solution:

Repair ipad 2~ Maxim ~ 09/19/2016

How much will it cost to fix the cable on the iPad 2? I just dropped the iPad and now my screen is broken and everything else works flawlessly.

Macsave Center Answer: Maxim, good afternoon!
Cost 1500 rub.

...~ Boomchik ~ 02-07-2016

The display of the iPad mini was broken and then it stopped turning on. What should I do?

Macsave Center Answer: Good afternoon, you need to look at it and make a diagnosis, bring it to us. Our diagnostics are free

Subject of the question ~ Margarita ~ 05/30/2016

Good day! I was sitting on the iPad, put it on lock, wanted to sit again and it wouldn’t turn on, I tried all the methods that are written here, it doesn’t help

Macsave Center Answer: Good afternoon, I need some diagnostics

IPAD MINI does not turn on ~ Rustem ~ 05/24/2016

Hello! My situation is this. In the winter, everything works, but from May to September it does not turn on. At the same time, the stripes are colored, the apple is distorted, or the screen is multi-colored. But you just need to warm it up a little (lay it in the sun or a little with a hairdryer) and that’s it turns on and works. Tried to restore via iTunes. Restored, the problem remained. Purchased in 2013. Thanks in advance.

Macsave Center Answer: Good afternoon, I need to get diagnosed.

Topic of the question ~ Evgeniy ~ 05/19/2016

Macsave Center Answer: Good afternoon, I need to diagnose it, maybe I need to flash it.

Topic of the question ~ Dasha ~ 09/14/2015

please tell me, when charging my iPad turns on and off, and so on every five minutes, but there’s really no charge? what is the reason?

If a black screen suddenly appears on your iPad, this is not a happy sign, then there is a problem with the tablet. If the iPad has a black screen, what should I do? The black screen may appear periodically or for the first time, it has no meaning how many times this happened, it is better to contact the service center before the device completely stops working. The service will diagnose your tablet and correctly determine the cause of the problem.

If a problem occurs with the screen, the picture on the display may freeze or may not respond to tactile presses on the touch screen. It happens that the iPad can connect, and not fully load, freeze for a long time. All this is evidence that the internal part of the device is broken, there are either missing contacts or damage. In this article we will describe possible reasons the occurrence of a black screen and ways to solve the problem.

One of the obvious reasons is a malfunction of the microcircuit that is responsible for the operation of the screen. As a rule, this happens due to an unsuccessful fall of the iPad, sudden pressure on the case, an impact, or spilling liquid on the tablet. The problem is resolved by replacing the failed microcircuit. Of course, this repair should be carried out in a specialized center.

If you are used to using the tablet in a cold or damp room, then the temperature difference may cause moisture condensation to form inside the tablet, which will damage the chip or negatively affect the cable, resulting in a lack of power to the screen, and then a black screen appears. Therefore, the diagnostics carried out in the service will correctly determine the exact cause of the non-working condition.

As a result of a shake or blow to the body of the iPad, the display may have been damaged or the cable from the board may have become disconnected, or it may have become out of working order. PCB or another mechanism within the system, it is clear that this is not system error, so reinstalling programs or the operating system will not help. It's clean technical problem, leading to the replacement of parts or mechanisms of the iPad. You may be lucky if a cable or other contact has simply become disconnected, then the repair will be minimal and quick. In any case, it is better to establish the cause of the problem in your presence to avoid misunderstandings.

What to do if iPad freezes on startup

If you notice that when you start up, the image of the Apple logo hangs on the iPad screen for a long time, or maybe the blue, black and white screen, or even the red screen color does not go away for a long time, try connecting your tablet to the computer via USB cable and run on PC iTunes program. Next, forcefully turn off your iPad by holding down the “Sleep/Wake” and “Home” buttons for 10 seconds until the Apple logo appears, but do not release until the device recovery process occurs on the iPad screen. When an iPad recovery entry appears, click the “Update” button. At this process iOS will be updated on the tablet, but all data will remain on it.

If this is your first time encountering the problem of a black or frozen screen, first turn off your iPad or try to restart the tablet by pressing the Power button. Restarting the device will not destroy the data contained on the tablet, but will help clear a software error or cancel a command.

When you force the tablet to reboot, you need to hold down the “Sleep/Wake” button and the “Home” button for ten seconds until the “Apple” logo appears.

If the tablet, after a forced reboot, again displays a black screen or does not turn on at all, you can try charging it for at least one hour. After ten minutes iPad screen should display the charging process, if this does not happen, the device may not be receiving power and is not charging.

This could be due to a faulty USB connector or a broken USB cable. Most quick way— change the cable or adapter to another one. If the same thing happens, try changing the charging socket or cleaning it by soaking an ear stick in alcohol.

Fair, not overpriced and not underestimated. There should be prices on the Service website. Necessarily! without asterisks, clear and detailed, where technically possible - as accurate and concise as possible.

If spare parts are available, up to 85% of complex repairs can be completed in 1-2 days. Modular repairs require much less time. The website shows the approximate duration of any repair.

Warranty and responsibility

A guarantee should be given for any repairs. Everything is described on the website and in the documents. The guarantee is self-confidence and respect for you. A 3-6 month warranty is good and sufficient. It is needed to check quality and hidden defects that cannot be detected immediately. You see honest and realistic terms (not 3 years), you can be sure that they will help you.

Half the battle is Apple repair- this is the quality and reliability of spare parts, so a good service works with suppliers directly, there are always several reliable channels and your own warehouse with proven spare parts for current models, so that you do not have to waste extra time.

Free diagnostics

This is very important and has already become a rule of good manners for service center. Diagnostics is the most difficult and important part of the repair, but you don't have to pay a penny for it, even if you don't repair the device based on its results.

Service repairs and delivery

Good service values ​​your time, so he offers free shipping. And for the same reason, repairs are carried out only in the workshop of a service center: correctly and according to technology can only be done in a prepared place.

Convenient schedule

If the Service works for you, and not for itself, then it is always open! absolutely. The schedule should be convenient to fit in before and after work. Good service works on weekends and holidays. We are waiting for you and working on your devices every day: 9:00 - 21:00

The reputation of professionals consists of several points

Company age and experience

Reliable and experienced service has been known for a long time.
If a company has been on the market for many years and has managed to establish itself as an expert, people turn to it, write about it, and recommend it. We know what we are talking about, since 98% of incoming devices in the service center are restored.
Other service centers trust us and refer complex cases to us.

How many masters in areas

If there are always several engineers waiting for you for each type of equipment, you can be sure:
1. there will be no queue (or it will be minimal) - your device will be taken care of right away.
2. you give to Macbook repair an expert in the field of Mac repairs. He knows all the secrets of these devices

Technical literacy

If you ask a question, a specialist should answer it as accurately as possible.
So that you can imagine what exactly you need.
They will try to solve the problem. In most cases, from the description you can understand what happened and how to fix the problem.